[ROM][L]CyanogenMod12.1

[mardon]

Neue nightly build 05.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[Gregu]

Hey, können Sie an dieser foo sucht TQS_S_2.6.ini

# INI Generator version 1.4; Aligned to TS version 6.1.2.0.27
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 1:   Non FEM-dependant section
#------------------------------------------------------------------------------------------------------------------------------------------------------------
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 1.1: General parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
TXBiPFEMAutoDetect  = 00 # Length: 1; Unit: Options (0: Manual Mode, 1: Automatic mode); Format: Unsigned; Source: Customer; Comment: This parameter is used by the FW to decide if the front-end is determined automatically or manually
TXBiPFEMManufacturer  = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit1,0: used to determine which FEM vendor type is used on the platform (0: RFMD, 1: TQS, 2:SKW, 3:HP), Bit3,2: unused, Bit7-4:External/internal load (4-SKW SB, 5-SKW HB, 6-HP SB, 7-HP HB)
RefClk  = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit 0,1,2-0:19.2MHz,1:26MHz,2:38.4MHz[Default],3:52MHz,4:38.4MHz XTAL,5:26MHz XTAL, Bit 3-CLK_REQ type, 0=wired-OR, 1=push-pull, Bit 4-CLK_REQ polarity
SettlingTime  = 05 # Length: 1; Unit: ms (0-15); Format: Unsigned; Source: Customer; Comment: The time from asserting CLK_REQ (low to high) to valid FREF clock on the device inputs
ClockValidOnWakeup  = 00 # Length: 1; Unit: Options (0: Reference clock not valid, 1: Reference clock is valid and stable); Format: Unsigned; Source: Customer; Comment: This parameter indicates whether the FREF clock is valid on wakeup
DC2DCMode  = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned, Source: Customer; Comment: Bit0 - DC2DC mode (0: btSPI is not used;1: btSPI used mux DC2DC to BT_FUNC2), Bit1- Level shifter support (0: No LS, 1: With LS)
Single_Dual_Band_Solution  = 01 # Length: 1; Unit: Options (0: Single band, 1: Dual band); Format: Unsigned; Source: Customer; Comment: This parameter indicates if the solution is single band (2.4GHz only) or dual band (2.4GHz & 5GHz)
Settings  = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit0-NBI(0:Off,1:On),Bit1-Telec ch14(0:Off,1:On),Bit2-FEM0-LB,Bit3-FEM0-HB,Bit4-FEM1-LB,Bit5-FEM1-HB-TX BiP load(0:Int.,1:Ext.),Bit6-LPD LB,Bit7-LPD HB
SRState = 00 # Length: 1; Unit: Options (0: Disabled, 1: Enabled); Format: Decimal; Source: TI; Comment: Smart Reflax (proprietary mechanism of TI that identify the silicon process specific params) state
SRF1 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 0F 3F  # Length: 16; Unit: SRF1 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
SRF2 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SRF2 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
SRF3 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SRF3 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
#SR_Debug_Table = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SR_Debug_Table values; Format: Signed; Source: TI; Comment: SR Debug values – for TI internal use only
#SR_SEN_N_P = 22 # Length: 1; Unit: SR_SEN_N_P values; Format: Unsigned; Source: TI; Comment: SR Debug values – for TI internal use only
#SR_SEN_N_P_Gain = a9 # Length: 1; Unit: SR_SEN_N_P_GAIN values; Format: Unsigned; Source: TI; Comment: SR Debug values – for TI internal use only
#SR_SEN_NRN = c1 # Length: 1; Unit: SR_SEN_NRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values – for TI internal use only
#SR_SEN_PRN = 8d # Length: 1; Unit: SR_SEN_PRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values – for TI internal use only
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 1.2: Band-dependant parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 1.2.1: 2.4G parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
RxTraceInsertionLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss
TXTraceLoss_2_4G = 24 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board
RxRssiAndProcessCompensation_2_4G  = EC F6 00 0C 18 F8 FC 00 08 10 F0 F8 00 0A 14 # Length: 15; Unit: 1/8dB; Format: Signed; Source: TI; Comment: The RSSI corner points are determined during RSSI temperature and process characterization
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 1.2.2: 5G parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
RxTraceInsertionLoss_5G  = 00 00 00 00 00 00 00 # Length: 7; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss
TxTraceLoss_5G  = 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 # Length: 35; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board
#------------------------------------------------------------------------------------------------------------------------------------------------------------
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 2:     FEM-dependant section
#------------------------------------------------------------------------------------------------------------------------------------------------------------
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 2.1:   FEM parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
#
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 2.1.1: 2.4G parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
FEM1_TXBiPReferencePDvoltage_2_4G = 0177 # Length: 1; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector
FEM1_TxBiPReferencePower_2_4G  = 80 # Length: 1; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage .
FEM1_TxBiPOffsetdB_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer
FEM1_TxPerRatePowerLimits_2_4G_Normal = 20 22 22 22 22 29 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
FEM1_TxPerRatePowerLimits_2_4G_Degraded = 1D 1D 1D 1D 1D 28 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
FEM1_TxPerRatePowerLimits_2_4G_Extreme = 19 19 19 19 19 25 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
FEM1_DegradedLowToNormalThr_2_4G = 30 # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
FEM1_NormalToDegradedHighThr_2_4G = 45 # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
FEM1_TxPerChannelPowerLimits_2_4G_11b = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
FEM1_TxPerChannelPowerLimits_2_4G_OFDM = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
FEM1_TxPDVsRateOffsets_2_4G = 01 02 02 02 02 00 # Length: 6; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group
FEM1_TxIbiasTable_2_4G  = 11 11 15 11 15 0F # Length: 6; Unit: Codeword ; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM. Options (MCS7, 54/48, 36/24, 18/12, 9/6, 11b)
FEM1_RxFemInsertionLoss_2_4G  = 12 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x
#------------------------------------------------------------------------------------------------------------------------------------------------------------
# SECTION 2.1.2: 5G parameters
#------------------------------------------------------------------------------------------------------------------------------------------------------------
FEM1_TxBiPReferencePDvoltage_5G  = 019A 01AE 01C2 01CC 01DB 01DB 01D1 # Length: 7; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector
FEM1_TxBiPReferencePower_5G = 80 80 80 80 80 80 80 # Length: 7; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage . The TX BiP reference power is linked to the TX BiP reference PD voltage
FEM1_TxBiPOffsetdB_5G = 00 00 00 00 00 00 00 # Length: 7; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer
FEM1_TxPerRatePowerLimits_5G_Normal  = 1C 1E 21 23 25 50 25 # Length: 7; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temperature range in which the FEM is operating
FEM1_TxPerRatePowerLimits_5G_Degraded  = 18 1E 21 23 25 50 24 # Length: 7; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temperature range in which the FEM is operating
FEM1_TxPerRatePowerLimits_5G_Extreme = 16 1C 1E 20 20 50 1E # Length: 7; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temperature range in which the FEM is operating
FEM1_DegradedLowToNormalThr_5G = 1E # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temperature range in which the FEM is operating
FEM1_NormalToDegradedHighThr_5G = 2D # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temperature range in which the FEM is operating
FEM1_TxPerChannelPowerLimits_5G_OFDM  = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 35; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
FEM1_TxPDVsRateOffsets_5G  = 01 02 02 02 02 00 02 # Length: 7; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group
FEM1_TxPDVsChannelOffsets_5G = 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 # Length: 35; Unit: 1/8dB; Format: Signed; Source: TI/Customer; Comment: This parameter is a power detector offset value used to correct the power detector curve for each channel
FEM1_TxPDVsTemperature_5G = 00 00 00 00 00 00 00 00 00 00 00 00 00 00 # Length: 14; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each temperture
FEM1_TxIbiasTable_5G  = 10 10 10 10 10 10 10 # Length: 7; Unit: Codeword; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM
FEM1_RxFemInsertionLoss_5G  = 10 10 10 10 10 10 10 # Length: 7; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL128x

Mit diesen Einstellungen in dieser Datei wifi normal arbeitet und verfügt über 20 MB

 

[mardon]

Neue nightly build 09.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

Ebenfalls wurden die GApps Pakete geupdated

 

[mardon]

Neue nightly build 12.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

Ebenfalls wurden die GApps Pakete geupdated

 

[mardon]

Neue nightly build 13.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Neue nightly build 16.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

Ebenfalls wurden die GApps Pakete geupdated

 

[mardon]

Die neue Sony Music App wurde nun auf Version 9.0.4.A.1.1beta geupdated, die flashable zip ist im 1sten Post unter Addons zu finden.

 

[mardon]

Neue nightly build 20.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Die neue Sony Music App wurde nun auf Version 9.0.4.A.1.2beta geupdated, die flashable zip ist im 1sten Post unter Addons zu finden.

 

[mardon]

Neue nightly build 21.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Neue nightly build 23.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

Ebenfalls wurden die GApps Pakete geupdated

 

[mardon]

Neue nightly build 27.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Neue nightly build 30.09.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Die neue Sony Music App wurde nun auf Version 9.0.4.A.2.0beta geupdated, die flashable zip ist im 1sten Post unter Addons zu finden.

 

[mardon]

Die Sony Video App wurde in Version 9.4.A.1.4.beta geadded, die flashable zip ist im 1sten Post unter Addons zu finden.

 

[mardon]

Neue nightly build 06.10.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

Ebenfalls wurden die GApps Pakete geupdated

 

[mardon]

Neue nightly build 07.10.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Die XperiaKeyboard flashable zip im 1sten Post unter Addons wurde auf Version 6.7.A.0.90 geupdated

 

[mardon]

Neue nightly build 11.10.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.

 

[mardon]

Neue nightly build 14.10.2015-OTA von mir via OTA released

DL im Startpost oder via OTA updater
CL im 3ten Post

Die OTA App speichert die zip auf der SD-Karte /sdcard/OTA-Updater/download/ROM/<romid>__<version.zip>.

Flashen dann wie immer erst Kernel via fastboot dann Rom zip via recovery flashen.

Da das kompilieren des Roms bisher immernoch failt (letzter Schritt, Packen der zip) hab ich nun die zip wieder selber per Hand gepackt.